NETWORK ENGINEER BLOG

Tips and Reviews for Engineers

NetApp FAS2040 初期設定例

ネットワークシステムとアプリケーションが融合するクラウド時代。ネットワークエンジニアは、ネットワークをベースにサーバーやストレージ、セキュリティにも対応できる「ICT エンジニア」としてのマインドとスキルが不可欠になりました。出典:@IT 自分戦略研究所
NetApp を中心にストレージも少しずつ勉強していきたいと思います。

FAS2040> setup
The setup command will rewrite the /etc/rc, /etc/exports,       
/etc/hosts, /etc/hosts.equiv, /etc/dgateways, /etc/nsswitch.conf,       
and /etc/resolv.conf files, saving the original contents of       
these files in .bak files (e.g. /etc/exports.bak).       
Are you sure you want to continue? [yes] yes       
 NetApp Release 7.3.2: Thu Oct 15 04:17:39 PDT 2009      
 System ID: 0135107715 (FAS2040)      
 System Serial Number: 850000026045 (FAS2040)      
 System Rev: A6      
 System Storage Configuration: Mixed-Path      
 System ACP Connectivity: No Connectivity      
 slot 0: System Board      
                Processors:         2       
                Memory Size:        4096 MB       
 slot 0: Private BGE 10/100 Ethernet Controller      
  e0P MAC Address:    00:a0:98:26:dd:b8 (auto-unknown-cfg_down)     
 slot 0: Dual 10/100/1000 Ethernet Controller G20      
  e0a MAC Address:    00:a0:98:26:dd:bd (auto-1000t-fd-up)     
  e0b MAC Address:    00:a0:98:26:dd:bc (auto-unknown-cfg_down)     
  e0c MAC Address:    00:a0:98:26:dd:bb (auto-unknown-cfg_down)     
  e0d MAC Address:    00:a0:98:26:dd:ba (auto-unknown-cfg_down)     
<...snip...>    
Please enter the new hostname [FAS2040]:        
Do you want to enable IPv6? [n]: n       
Do you want to configure virtual network interfaces? [n]: n       
Vif は、Network Interface を1つの論理インターフェースに集約します。  

Please enter the IP address for Network Interface e0a [192.168.253.45]:       
Please enter the netmask for Network Interface e0a [255.255.255.0]:       
Please enter media type for e0a {100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000)} [auto]: auto       
Please enter flow control for e0a {none, receive, send, full} [full]:        
Do you want e0a to support jumbo frames? [n]: y         
Please enter the IP address for Network Interface e0b :        
Please enter the IP address for Network Interface e0c : 10.1.1.1     
Please enter the netmask for Network Interface e0c [255.0.0.0]: 255.255.255.0       
Please enter media type for e0c {100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000)} [auto]:        
Please enter flow control for e0c {none, receive, send, full} [full]:        
Do you want e0c to support jumbo frames? [n]:        
Please enter the IP address for Network Interface e0d : 10.1.2.1       
Please enter the netmask for Network Interface e0d [255.0.0.0]: 255.255.255.0       
Please enter media type for e0d {100tx-fd, tp-fd, 100tx, tp, auto (10/100/1000)} [auto]:        
Please enter flow control for e0d {none, receive, send, full} [full]:        
Do you want e0d to support jumbo frames? [n]:        
Would you like to continue setup through the web interface? [n]: n       
yes を実行すると、http://filer_ip_address/api から初期 setup を web で実行する事が可能となります。例)e0 の IP が 10.10.10.10 の場合、 http://10.10.10.10/api

Please enter the name or IP address of the IPv4 default gateway [10.10.10.1]: 
The administration host is given root access to the filer's      

 /etc files for system administration.  To allow /etc root access      
 to all NFS clients enter RETURN below.      
Please enter the name or IP address of the administration host: 
administration host を指定すると、filer の root system (/vol/vol0 by default) は、これにアクセスできます。尚、アクセスには NFS を使用します。

Please enter timezone [Japan]: 
Where is the filer located? : FAS2040@UN       

What language will be used for multi-protocol files (Type ? for list)?:ja

Setting language on volume vol0 
 
The new language mappings will be available after reboot 
Thu Jan 20 15:12:18 JST [vol.language.changed:info]: Language on volume vol0 changed to ja 
Language set on volume vol0 
 
Do you want to run DNS resolver? [n]: n 
Do you want to run NIS client? [n]: n 
 
 The Baseboard Management Controller (BMC) provides remote management capabilities
 including console redirection, logging and power control.
 It also extends autosupport by sending down filer event alerts.
 
Would you like to configure the BMC [y]: n 
 The Shelf Alternate Control Path Management process provides the ability
 to recover from certain SAS shelf module failures and provides a level of
 availability that is higher than systems not using the Alternate Control
 Path Management process.
BMC を有効にするとリモートで、コンソール制御、logging、Power 制御が可能となります。
BMC が正常に機能しているかどうかを確認するには、storage system promp: で以下を実行します。
storage system promp:  "bmc test autosupport"
* BMC: Baseboard Management Controller

Do you want to configure the Shelf Alternate Control Path Management interface for SAS shelves [n]:  
The initial aggregate currently contains 3 disks;  you may add more
disks to it later using the "aggr add" command.
Now type 'reboot' for changes to take effect. 
FAS2040> reboot